Views

Difference between revisions of "optiPoint 410/420 CorNet IP (HFA) to SIP migration"

The Wiki of Unify contains information on clients and devices, communications systems and unified communications. - Unify GmbH & Co. KG is a Trademark Licensee of Siemens AG.

Jump to: navigation, search
(Subscriber number is not prompted)
 
(44 intermediate revisions by 4 users not shown)
Line 1: Line 1:
This migration procedure is for upgrading an optiPoint 410/420 CorNet IP phone V5.1.2x to SIP V6.0.56 and later.
+
{{Breadcrumb|0|0|Clients & Devices|optiPoint|optiPoint 410/420}}
 +
{{Discontinued|en|Devices}}
  
=== Connect the phone to LAN ===
 
Connect the optiPoint Cornet IP phone to the [[LAN]] (<code>DHCP=on</code> is default). The assumption is that [[DHCP]] is available in your local area network.
 
The phone will reboot.
 
  
Depending on the version of the CorNet IP application installed  
+
This migration procedure is for upgrading an [[optiPoint 410/420]] CorNet IP phone V5.1.2x to [[SIP]] V6.0.56 and later.
* either you may be prompted to enter the Fully qualified subscriber number, then follow [[#Subscriber number prompted|Subscriber number prompted]]
+
The procedure can be performed on a per phone basis (local admin menu or via [[WBM]]) - described on this page - or, starting with [[optiPoint_410/420_S_Release_Notes#V7_R4.1.0|V7R4.1.0]], via [[DLS]].
* or you may '''not''' be prompted to enter the Fully qualified subscriber number, then follow [[#Subscriber number is not prompted|Subscriber number is not prompted]].
+
== Precondition ==
 +
Please check your hardware revision against the data in the product release note (section "Hardware revisions supported") as not all HW revisions shipped with CorNet IP protocol will support SIP. See also [[SIP V6.0 optiPoint compatibility|optiPoint HW compatibility]].
 +
 
 +
== Connect the phone to LAN ==
 +
# Connect the optiPoint CorNet IP phone to the [[LAN]] (<tt>DHCP=on</tt> is default). The assumption is that [[DHCP]] is available in your local area network. The phone will reboot.
 +
# Depending on the version of the CorNet IP application installed  
 +
:* either you may be prompted to enter the subscriber number, then continue with [[#Subscriber number is prompted|Subscriber number is prompted]]
 +
:* or you may '''not''' be prompted, then continue with [[#Subscriber number is not prompted|Subscriber number is not prompted]].
 +
 
 +
== Fully qualified subscriber number ==
  
 
=== Subscriber number is prompted ===
 
=== Subscriber number is prompted ===
  
# Enter some digits like [[Image:opk-1.png]] [[Image:opk-2.png]] [[Image:opk-3.png]] ???
+
# Enter your fully qualified subscriber number.
# Confirm <code>Save Changes</code> with the [[Image:opk-ok.png]] key.  
+
# Confirm <tt>Save Changes</tt> with the [[Image:opk-ok.png]] key.<br>The display shows:<br><tt>Administration</tt><br><tt>01=Configuration?</tt>
# The display will show:<br><code>Administration</code><br><code>01=Configuration?</code>
+
Continue with [[#Detect the phone's IP address|Detect the phone's IP address]].
# Press the [[Image:opk-ok.png]] key.
 
Continue with [[#Enter Admin password|Enter Admin password]].
 
  
==== Subscriber number is not prompted ====
+
=== Subscriber number is not prompted ===
  
If you have not been prompted for the subscriber number, the display will show:
+
If you have not been prompted for the subscriber number, the display will show <tt>Invalide GW Adress</tt> or <tt>No subscriber number</tt>.
  
<code>Invalide GW Adress</code> or <code>No suscriber number</code>
+
# Press the [[Image:opk-ok.png]] key.<br>The display shows:<br><tt>Administration</tt><br><tt>01=Configuration?</tt>
 +
# Continue with [[#Detect the phone's IP address|Detect the phone's IP address]].
  
# Press the [[Image:opk-ok.png]] key.
+
== Detect the phone's IP address ==
# The display will show:<br><code>Administration</code><br><code>01=Configuration?</code>
 
# Press the [[Image:opk-ok.png]] key once more.
 
  
=== Enter Admin password ===
+
# Press the [[Image:opk-ok.png]] key. The display shows:<br><tt>Enter admin password</tt><br><tt>_</tt>
The display will show:<br><code>Enter admin password</code><br><code>_</code>
+
# Enter the admin password (default: [[Image:opk-1.png]] [[Image:opk-2.png]] [[Image:opk-3.png]] [[Image:opk-4.png]] [[Image:opk-5.png]] [[Image:opk-6.png]].<br>The display shows:<br><tt>Config:</tt><br><tt>01=Network?</tt>
# Press key pad for digits [[Image:opk-1.png]] [[Image:opk-2.png]] [[Image:opk-3.png]] [[Image:opk-4.png]] [[Image:opk-5.png]] [[Image:opk-6.png]], which is the factory default password.
+
# Press the [[Image:opk-ok.png]] key and the [[Image:opk-re.png]] key to select <tt>02=Terminal IP addr.?</tt>.
 +
# You may read the IP address and use this to switch over to the [[WBM]] by using a web browser (Microsoft Internet Explorer recommended).
  
5) Display will show
+
Continue with [[#Download new firmware|Download new firmware]].
 
Config:
 
01=Network?
 
  
Press confirmation key  () and the right arrow key to select
+
== Download new firmware ==
+
# In the Web browser's URL row type in <tt>https://Phone-IP-Address</tt>, e.g. <tt>https://192.168.1.2</tt> or <tt>http://Phone-IP-Address:8085</tt>, e.g. <tt>http://192.168.1.2:8085</tt>.
02=Terminal IP addr.?
 
  
You may read the IP address and use this to switch over to the Web Admin pages by using a web browser (Microsoft IE recommended), typing http://Phone-IP-Address:8085, e.g. http://192.168.1.2:8085
+
# Enter the <tt>Administration</tt> menu (default password: ''123456'').
 +
# Select the <tt>Upload/Download</tt> section.
 +
# Select <tt>Download application</tt>.
 +
# Start a standard [[FTP]] server (e.g. [http://support.3com.com/software/utilities_for_windows_32_bit.htm 3Com Daemon]), and fill out the relevant FTP data, refer to the screenshot below.<br>[[Image:wbm-op410-420-ftp.gif|200px|'''File transfer''' screenshot in optiPoint 410/420 phone WBM]]
 +
# Continue with [[#Restore factory settings|Restore factory settings]].
  
6) Enter the Administration menu (PW 123456) and go to the “Upload/Download” section, choose “Download application”.
+
== Restore factory settings ==
Start a standard FTP Server (e.g. 3Com Daemon), and fill out the relevant FTP data, example pls. Refer to the screen shot below:
 
  
7) After successful restart of the application, it is recommended to perform a Restore of factory settings in the Web Admin, the reset PW  is 124816.
+
After successful restart of the application, it is recommended to perform a factory reset.
  
This has to be removed here later: {{File-DL|Quick Guide Migrating CorNet-IP to SIP|pdf}}
+
* How to [[optiPoint 410/420 S factory reset]]

Latest revision as of 14:04, 17 December 2014

The support for this product has been discontinued!
Please visit Devices to get further information about the current product portfolio.


This migration procedure is for upgrading an optiPoint 410/420 CorNet IP phone V5.1.2x to SIP V6.0.56 and later. The procedure can be performed on a per phone basis (local admin menu or via WBM) - described on this page - or, starting with V7R4.1.0, via DLS.

Precondition

Please check your hardware revision against the data in the product release note (section "Hardware revisions supported") as not all HW revisions shipped with CorNet IP protocol will support SIP. See also optiPoint HW compatibility.

Connect the phone to LAN

  1. Connect the optiPoint CorNet IP phone to the LAN (DHCP=on is default). The assumption is that DHCP is available in your local area network. The phone will reboot.
  2. Depending on the version of the CorNet IP application installed

Fully qualified subscriber number

Subscriber number is prompted

  1. Enter your fully qualified subscriber number.
  2. Confirm Save Changes with the opk-ok.png key.
    The display shows:
    Administration
    01=Configuration?

Continue with Detect the phone's IP address.

Subscriber number is not prompted

If you have not been prompted for the subscriber number, the display will show Invalide GW Adress or No subscriber number.

  1. Press the opk-ok.png key.
    The display shows:
    Administration
    01=Configuration?
  2. Continue with Detect the phone's IP address.

Detect the phone's IP address

  1. Press the opk-ok.png key. The display shows:
    Enter admin password
    _
  2. Enter the admin password (default: opk-1.png opk-2.png opk-3.png opk-4.png opk-5.png opk-6.png.
    The display shows:
    Config:
    01=Network?
  3. Press the opk-ok.png key and the opk-re.png key to select 02=Terminal IP addr.?.
  4. You may read the IP address and use this to switch over to the WBM by using a web browser (Microsoft Internet Explorer recommended).

Continue with Download new firmware.

Download new firmware

  1. In the Web browser's URL row type in https://Phone-IP-Address, e.g. https://192.168.1.2 or http://Phone-IP-Address:8085, e.g. http://192.168.1.2:8085.
  1. Enter the Administration menu (default password: 123456).
  2. Select the Upload/Download section.
  3. Select Download application.
  4. Start a standard FTP server (e.g. 3Com Daemon), and fill out the relevant FTP data, refer to the screenshot below.
    File transfer screenshot in optiPoint 410/420 phone WBM
  5. Continue with Restore factory settings.

Restore factory settings

After successful restart of the application, it is recommended to perform a factory reset.