Difference between revisions of "optiPoint 150 S Release Notes"
The Wiki of Unify contains information on clients and devices, communications systems and unified communications. - Unify GmbH & Co. KG is a Trademark Licensee of Siemens AG.
| Line 4: | Line 4: | ||
=== What’s New? === | === What’s New? === | ||
| + | * IP: New L3-QoS default parameters: Signalling: AF31 (DSCP 26) and RTP: EF (DSCP 46) | ||
| + | * HiPath 300 | ||
=== Fixed Bugs === | === Fixed Bugs === | ||
| − | + | * HiPath 3000: No Ringback tone when calling Upoe or HFA phone | |
| − | + | * Admin: Configuration of Call forwarding on the phone (type set to HP3k, HP4k) | |
| + | * IP: Phone send ARP requests to IP: 192.1.1.49 | ||
== V1.25 == | == V1.25 == | ||
| − | |||
| − | |||
=== Fixed Bugs === | === Fixed Bugs === | ||
| − | + | * General: Possibiliy to use special characters in SIP-ID like (@, /, %) needed for registration on some of the SIP providers. | |
| − | |||
== V1.24 == | == V1.24 == | ||
| Line 43: | Line 43: | ||
=== What’s New? === | === What’s New? === | ||
| − | + | * Telnet port disabled | |
| − | + | * Distinctive Ringing (Sylantro) supported | |
| − | |||
| − | |||
Revision as of 14:02, 28 August 2006
The optiPoint 150 S Release Notes describe descending sorted new features, fixed firmware bugs und open issues for the appropriate firmware versions of the optiPoint 150 S (
optiPoint 150 S).
Contents
V1.26
What’s New?
- IP: New L3-QoS default parameters: Signalling: AF31 (DSCP 26) and RTP: EF (DSCP 46)
- HiPath 300
Fixed Bugs
- HiPath 3000: No Ringback tone when calling Upoe or HFA phone
- Admin: Configuration of Call forwarding on the phone (type set to HP3k, HP4k)
- IP: Phone send ARP requests to IP: 192.1.1.49
V1.25
Fixed Bugs
- General: Possibiliy to use special characters in SIP-ID like (@, /, %) needed for registration on some of the SIP providers.
V1.24
What’s New?
- Support of DNS query SRV (DNS_SRV)
- Support DNS TTL
- Support RFC 3264 Hold for Broadsoft
Fixed Bugs
- General: alphanumeric SIP_ID’s now possible (e.g. vorname.nachname@provider.com)
- General: Loud tone when call disconnected
- General: Calltransfer not possible after toggle between calls
- LAN: phone doesn’t register, if L2 QoS value is set
- LAN: VLAN ID can’t be reset to None
- HiPath 3000: Toggle between calls not possible
- HiPath 3000: Busy tone after attended Call transfer
- HiPath 3000: HP3k-HP3k trunking, no payload after transfer
- Phone GUI: Remove possibility to configure Call Forwarding when connected to HiPath 2000, HiPath 3000, HiPath 4000, HiPath 5000
Known & Open Issues
- HiPath 3000: Blind (semi-attended) transfer doesn’t work
- Not possible to dial, after first call was made with Hook on
- Symmetric use of UDP ports (planned for V1.25)
V1.23
What’s New?
- Telnet port disabled
- Distinctive Ringing (Sylantro) supported
