optiPoint 150 S Release Notes
The Wiki of Unify contains information on clients and devices, communications systems and unified communications. - Unify GmbH & Co. KG is a Trademark Licensee of Siemens AG.
The optiPoint 150 S Release Notes describe descending sorted new features, fixed firmware bugs und open issues for appropriate firmware versions of the optiPoint 150 S (
optiPoint 150 S).
Contents
V1.30 (still under validation)
What’s New?
- Be able to disable *99 at Sylantro
Fixed Bugs
- Wrong display message at Op150 after call transfer
- No Fallback to Inland DTMF if RFC2833 configured but one partner does not support DTMF after RFC2833
- Number not dialed when going Off Hook
- No automatic callback if a semi-attended transfer is initiated before Ringing.
- No Ringtone when using enquiry from OP150S to OP410 HFA phone (Just like CAFT 400)
- Semi Attended TRansfer does not work on HiPath 2000
- DNS TTL does not work
- Sylantro ID1.6 Inbound Call when Busy LCD display error
- Sylantro ID3.6 Call-Waiting Interrupted LCD display error
- Call log list always shows the oldest entry at first
- Phone plays DTMF digits if called while dialing.
- Providertest Web.de: No Registration with DNS Name for SIP Server
V1.28
What’s New?
| Internal ID | Cluster | New feature | Comment |
|---|---|---|---|
| N/A | Sylantro | Special call park feature for Sylantro V4.0 | Fixed |
| N/A | Sylantro | Special call pick-up feature for Sylantro V4.0 | Fixed |
| N/A | Sylantro | Distinctive ringing for Sylantro V4.0 | Fixed |
Fixed Bugs and new features since Version 1.22
- Broadsoft: DHCP Trouble - phone couldn't obtain IP adress via DHCP shortly
- Broadsoft: Should not perform SRV lookup if service domain IPv4 format
- Broadsoft: Failover/failback mechanism
- Broadsoft: Support RFC 3264 Hold for Broadsoft
- IP: New default QoS L3 values (Signalling: AF31 (DSCP 26) and RTP: EF (DSCP 46)
- Admin: Possible to configure Call forwarding at the phone when connected to HP3k, HP4k)Now neither WBM nor local admin can configure CF in this case
- General: Possibiliy to use special characters in SIP-ID like (@, /, %) needed for registration on some of the SIP providers.
- Support of DNS query SRV (DNS_SRV)
- General: alphanumeric SIP_ID’s now possible (e.g. vorname.nachname@provider.com)
- General: Short loud tone when call disconnected (after hook-on for about 200 ms)
- General: Calltransfer not possible after toggle between calls
- General: The "Port field" in the SIP settings should aleady have a default value 5060.
- General: To stay conform with other Siemens phones the default Codec Settings of the OP150S should be changed to "G.711A > G.711U > G.72x"
- General: Not possible to dial after first call was made with Hook on.
- General: Telnet access to optiPoint 150 S
- LAN: phone doesn’t register, if L2 QoS value is set
- LAN: VLAN ID can’t be reset to None
- HiPath 3000: Toggle between calls not possible
- HiPath 3000: Do not disturb is not working
- HiPath 3000: No Ringback tone when calling Upoe or HFA phone @ HP3k (complies now to RFC 3960 sect 3.2)
- HiPath 3000: Busy tone after attended Call transfer
- HiPath 3000: HP3k-HP3k trunking, no payload after transfer
- Phone GUI: Remove possibility to configure Call Forwarding when connected to HiPath 2000, HiPath 3000, HiPath 4000, HiPath 5000
- Telnet port disabled
- Sylantro: Distinctive Ringing (Sylantro) supported
Known & Open Issues
- HiPath 3000: Blind (semi-attended) transfer doesn’t work
- Not possible to dial, after first call was made with Hook on
- Symmetric use of UDP ports
V1.22
Fixed Bugs and new features:
- VLAN ID can't be configured via Phone
- Blind transfer does not work oh H8000
- After factory reset it is still possible to log in as user defined in last saved configuration
- Admin password is not reset after factory reset
- Disable Telnet Access at the optiPoint 150
