Difference between revisions of "Collaboration with VoIP Providers"

Revision as of 13:15, 13 April 2007

Collaboration with VoIP Providers is an important topic in the todays world of Voice/Data Communication over the Internet. The following information will give an overview of the supported VoiP providers in the different countries as well as additional considerations and hints to the connected platforms.

Overview

HiPath Platforms have been tested with a large number of Internet telephony providers that support SIP. At the moment, there are vast differences in the range of features supported, reachable networks, and service quality offered by the various providers. Occasionally configuration changes may occur that require adjustments to be made to the HiPath Platforms.

General Information by platform

HiPath BizIP

HiPath BizIP's main functions have been tested on a large number of Internet telephony providers that support SIP. At the moment, there are differences in the range of features supported, reachable networks, and service quality offered by the various providers. For limitations or configuration changes please see release note at ftp://bizip.siemens.com/HiPath_BizIP1.0.
HiPath BizIP supports:

• One active SIP provider
• Up to 10 SIP user accounts
• SIP Direct Inward Dialling with V1.0.3
• Up to 8 simultaneous VoIP connections, depending on DSL bandwidth
• Parallel ISDN and VoIP connections

HiPath 2000

The HiPath 2000 V1.0 introduced support of ITSPs (Internet Telephony Service Provider) supporting SIP Protocol over DSL Telephony since the release of SMR 6 (HE620Y.06.439) software version enhancing features, limits and capabilities with each new software version released.

HiPath 2000 V1.0 DSL Telephony features (Hints and restrictions):

• starting from HiPath 2000 V1.0 R9.5.0 (HE620Y.09.648):
  • STUN support is provided and the system now connects to external customers' Router performing NAT (Routing devices that perform Symmetrical NAT are not supported).
  • up to 4 active SIP Providers can be active at the same time on the system.
  • the complete DID range (ITSP providers dependant) is available for the SIP Clients.
  • DSL telephony can be operated in parallel with CorNet IP Trunking with no restrictions.
• up to HiPath 2000 V1.0 R7.0.0 (HE620Y.07.554):
  • DSL Routing (NAT) was performed by the system connected to external xDSL Modem or xDSL Router with routing (NAT) section disabled.
  • only one SIP Provider can be active on the system.
  • up to 30 SIP Clients (MSN) can be configured at the same time on the system.
  • DSL telephony can't be configured in parallel with CorNet IP Trunking.
• A maximum of 4 simultaneous connections to the SIP provider are supported per IP Phone (xDSL Bandwidth should be considered to prevent quality losses or service disruptions).
• Both S0 connections and SIP connections are supported in parallel via the Internet.

System-related connection conditions

HiPath 2000 V1.0 should be connected directly to the xDSL modem through WAN interface (with custom PPPoE or predefined SIP Provider settings).
Since R9.5.0, STUN is now supported allowing the HiPath 2000 to be operated behind 3rd party Router (NAT)/Firewall.

SIP Provider dependent restrictions:

• Special call numbers and emergency calls
  • Special call numbers (e.g. 0800, 0900, 0137) or analog fax/modem connections are not supported by all SIP providers.
  • Emergency call numbers (110, 112) are not supported since the local network cannot be clearly assigned when exiting into the public network. These connections must be implemented via S0 access and are generally provided in advance by the setup assistant.
  • Calling line identification
    The CLIP and CLIR features are implemented differently by the various providers. Limitations in the calling line identification may occur.
  • For connections that exit to the fixed/wireless network or come in from the fixed/wireless network:
    • Provider-internal connections (destination is busy/unregistered) Internal connections to a busy or unregistered user are generally correctly signaled.
    • Calls to other providers
      These calls are technically possible but the individual providers adapt the routing functions of their network to each particular business model. More information is available with the respective SIP provider.
• Call data evaluation
  The SIP protocol records individual call data against time. The data can be evaluated using an external application such as Teledata Office.
• DTMF transmission over SIP:
  • DTMF Inband Signalling happens by default.
  • Might be necessary to disable "DTMF transmission according to RFC 2833" when no DTMF tones passes via the DSL line.
  • Might be necessary to disable "DTMF Outband Signalling" at the same time and in some specific cases too.

• FAX via SIP Provider: FAX transmissions are routed via ISDN by default: HiPath 2000 V1.0 permits FAX transmissions to be routed via SIP provider but some issues should be considered:
  
  • FAX transmission is only possible with Codec G.711.
  • Automatic switchover from G.723 or G.729 to G.711 is not possible.
  • Most SIP Providers do not support T.38 FAX transmission over SIP since they haven't it yet fully implemented.
  • Packets losses may occur and be too high using Codec G.711 for FAX transmission over SIP via DSL connection due to higher bandwidth requirements of this codes compared to the others: FAX transmissions could be fully or partially incomplete.

Tested VoIP providers by countries

HiPath platforms main functions have been tested with the following Internet telephony providers that support SIP.
default = general access data is already available as default setting in the WBM,
x = has been successfully tested by development or customer,
DID = accounts for PBX-trunking / Direct Inward Dialling

Germany

Hungary

Test for the HiPath BizIP are currently going to be conducted with Externet

The Netherlands

United Kingdom

United States of America

Tests for the HiPath 2000 and HiPath 3000 are currently going to be conducted with Verizon

Documentation

Documentation in further languages, software and other downloads can be found on http://www.unify.com/ ⇒ Support. Any comments to the files provided here?

Administration and service

Release Notes

Sales Channels

See also

External Links

• Siemens Enterprise Business Area (SEBA) (Internet Explorer only)