Views

Difference between revisions of "optiPoint 410/420 S upgrade to SIP V6.0"

The Wiki of Unify contains information on clients and devices, communications systems and unified communications. - Unify GmbH & Co. KG is a Trademark Licensee of Siemens AG.

Jump to: navigation, search
 
(6 intermediate revisions by the same user not shown)
Line 1: Line 1:
<div class="breadcrumb">
+
{{Breadcrumb|0|0|{{dev-en}}|optiPoint|optiPoint 410/420 S}}
{{up}} [[How To]]
 
</div>
 
  
This information describes distinctions while upgrading optiPoint 410/420 phones to [[optiPoint 410/420 S general information to SIP V6.0|optiPoint 410/420 SIP V6.0]] Application Software.<br />
+
This information describes distinctions while upgrading optiPoint 410/420 S phones to [[optiPoint 410/420 S general information to SIP V6.0|optiPoint 410/420 SIP V6.0]] Application Software.
For common upgrade procedure (download application) refer to [[Firmware upgrade optiPoint 410/420 S phones]].<br />
 
  
For migration from CorNet IP (HFA) to SIP Application Software see [[Migrate optiPoint 410/420 CorNet IP (HFA) phones to SIP]].  
+
For common upgrade procedure (download application) refer to [[optiPoint 410/420 S firmware upgrade procedure]].
 +
 
 +
For migration from CorNet IP ([[HFA]]) to SIP Application Software see [[optiPoint 410/420 CorNet IP (HFA) to SIP migration]].  
  
 
== Possibilities of Upgrading ==
 
== Possibilities of Upgrading ==
Line 22: Line 21:
 
# Change the phone's [[VLAN]] discovery setting to <code>DHCP</code>, then back to <code>manual</code>, this action will store the setting in the phone’s database and the default value is not used
 
# Change the phone's [[VLAN]] discovery setting to <code>DHCP</code>, then back to <code>manual</code>, this action will store the setting in the phone’s database and the default value is not used
 
# Reboot the phone
 
# Reboot the phone
# Upgrade phone to [[SIP]] V6.0 (see [[Firmware upgrade optiPoint 410/420 S phones]])
+
# Upgrade phone to [[SIP]] V6.0 (see [[optiPoint 410/420 S firmware upgrade procedure]])
  
 
== Upgrading from SIP V4.1.15 or earlier versions ==
 
== Upgrading from SIP V4.1.15 or earlier versions ==
Line 32: Line 31:
 
# Change the phone's [[QoS]] L2 layer setting to <code>ON</code>, then back to <code>OFF</code> and reboot the phone, this action will store the setting in the phone’s database and the default value is not used.
 
# Change the phone's [[QoS]] L2 layer setting to <code>ON</code>, then back to <code>OFF</code> and reboot the phone, this action will store the setting in the phone’s database and the default value is not used.
  
 +
{{SeeAlso optiPoint 410/420 S}}
  
 
[[Category:optiPoint]]
 
[[Category:optiPoint]]
 
[[Category:Configuration]]
 
[[Category:Configuration]]

Latest revision as of 08:39, 11 August 2011

This information describes distinctions while upgrading optiPoint 410/420 S phones to optiPoint 410/420 SIP V6.0 Application Software.

For common upgrade procedure (download application) refer to optiPoint 410/420 S firmware upgrade procedure.

For migration from CorNet IP (HFA) to SIP Application Software see optiPoint 410/420 CorNet IP (HFA) to SIP migration.

Possibilities of Upgrading

The optiPoint 410/420 SIP V6.0 Application Software can be uploaded on the phone via FTP (if supported by the software being upgraded from):

  • Via the WBM interface (supported by all phone models)
  • Via the phone's local user interface (not supported by 410 entry S that hasn't the display)
  • Via HiPath DLS application (supported by V4.1.20 onwards, V5.0.x, V6.0.x and V7)

Upgrading from SIP V5.0.15 or earlier versions

In optiPoint 410/420 SIP V6.0 Application Software the VLAN discovery default setting is set to DHCP.

This may cause problem, when the phone was configured for manual VLAN discovery.

  1. Change the phone's VLAN discovery setting to DHCP, then back to manual, this action will store the setting in the phone’s database and the default value is not used
  2. Reboot the phone
  3. Upgrade phone to SIP V6.0 (see optiPoint 410/420 S firmware upgrade procedure)

Upgrading from SIP V4.1.15 or earlier versions

Note that QoS default settings are now set to ON (both on L2 and L3 layers).

This may cause problem when the phone sends tagged frames and your network devices can’t handle these tagged frames. In this case, we suggest the following workaround, before performing the upgrade:

  1. Change the phone's QoS L2 layer setting to ON, then back to OFF and reboot the phone, this action will store the setting in the phone’s database and the default value is not used.

See also