Views

Difference between revisions of "optiPoint 410/420 FAQ (general)"

The Wiki of Unify contains information on clients and devices, communications systems and unified communications. - Unify GmbH & Co. KG is a Trademark Licensee of Siemens AG.

Jump to: navigation, search
m (Q: My oP410/420 phone only supports power class 0 (default). How to setup the corresponding PoE-switch to reserve lower power?)
m (Q: My oP410/420 phone only supports power class 0 (default). How to setup the corresponding PoE-switch to reserve lower power?)
Line 4: Line 4:
 
: A: Some models of the first oP410/420 phones do not support power negotiation according IEEE 802.3af. For details refer to [[PoE classes of optiPoint phones]]. To avoid that the Lan-switch reserves to much Power and cannot support PoE on all LAN ports, the LAN ports should be forced to supply a specified power class. This is normally part of the switch administration.
 
: A: Some models of the first oP410/420 phones do not support power negotiation according IEEE 802.3af. For details refer to [[PoE classes of optiPoint phones]]. To avoid that the Lan-switch reserves to much Power and cannot support PoE on all LAN ports, the LAN ports should be forced to supply a specified power class. This is normally part of the switch administration.
 
e.g. [http://www.cisco.com/en/US/products/hw/switches/ps5528/prod_release_note09186a00804cc85f.html Settings for Cisco 3750, 3560, 2970 LAN switches]
 
e.g. [http://www.cisco.com/en/US/products/hw/switches/ps5528/prod_release_note09186a00804cc85f.html Settings for Cisco 3750, 3560, 2970 LAN switches]
 +
Search for: Allocating Power to Devices Connected to a PoE Port
  
 
==== Q: Can I run an optiPoint 410/420 with local '''and''' PoE power supply =====
 
==== Q: Can I run an optiPoint 410/420 with local '''and''' PoE power supply =====
 
: A: This is not recommended, although the phone will not break. Power class negotiation will not run properly, because the standard requires a ''power-less'' state for the negotiation (no local power supply). Thus in this case the class will be set to 0 (default). If the power negotiation is done first and then the local power supply is connected, the initial negotiated power class will not be changed.
 
: A: This is not recommended, although the phone will not break. Power class negotiation will not run properly, because the standard requires a ''power-less'' state for the negotiation (no local power supply). Thus in this case the class will be set to 0 (default). If the power negotiation is done first and then the local power supply is connected, the initial negotiated power class will not be changed.

Revision as of 12:08, 16 January 2007

Power over LAN

Q: My oP410/420 phone only supports power class 0 (default). How to setup the corresponding PoE-switch to reserve lower power?

A: Some models of the first oP410/420 phones do not support power negotiation according IEEE 802.3af. For details refer to PoE classes of optiPoint phones. To avoid that the Lan-switch reserves to much Power and cannot support PoE on all LAN ports, the LAN ports should be forced to supply a specified power class. This is normally part of the switch administration.

e.g. Settings for Cisco 3750, 3560, 2970 LAN switches Search for: Allocating Power to Devices Connected to a PoE Port

Q: Can I run an optiPoint 410/420 with local and PoE power supply =

A: This is not recommended, although the phone will not break. Power class negotiation will not run properly, because the standard requires a power-less state for the negotiation (no local power supply). Thus in this case the class will be set to 0 (default). If the power negotiation is done first and then the local power supply is connected, the initial negotiated power class will not be changed.