Views

Difference between revisions of "HiPath Cordless IP - Server HW"

The Wiki of Unify contains information on clients and devices, communications systems and unified communications. - Unify GmbH & Co. KG is a Trademark Licensee of Siemens AG.

Jump to: navigation, search
m (Some adaptations.)
Line 20: Line 20:
  
 
Order Number of this Server at Fujitsu is CUZ:1385V203-SEN08<br>
 
Order Number of this Server at Fujitsu is CUZ:1385V203-SEN08<br>
 +
 +
If you change the Motherboard of this Fujitsu Server please consider to apply the BIOS configuration reported below:
 +
 +
Advanced
 +
  > SATA Configuration
 +
    SATA Mode Selection: [AHCI]
 +
    Aggressive LPM Support [Enabled]
 +
<br>
 +
Server Mgmt
 +
  > Console Redirection
 +
    Com Port Address:          [Serial 1]
 +
    Baud Rate:                [115.2K]
 +
    Console Type:              [VT100]
 +
    Flow Control:              [None]
 +
<br>
 +
Boot
 +
  Boot priority order:
 +
    Boot Option #1: [P0: ST500NM0011]
 +
    Boot Option #2: [P4: TSSTcorp CDDVDW SN-208AB]
 +
    Boot Option #3: [Disabled]
  
 
=== Fujitsu PRIMERGY TX150 S7 (declared Phase Out by Fujitsu, superseded by TX150 S8) ===
 
=== Fujitsu PRIMERGY TX150 S7 (declared Phase Out by Fujitsu, superseded by TX150 S8) ===
Line 30: Line 50:
 
   > Advanced System Configuration
 
   > Advanced System Configuration
 
       SATA Mode Selection:        [AHCI]
 
       SATA Mode Selection:        [AHCI]
 
+
<br>
 
Server
 
Server
 
     > Console Redirection
 
     > Console Redirection
Line 38: Line 58:
 
         Flow Control:              [None]
 
         Flow Control:              [None]
 
         Continue C.R. after POST:  [Off]
 
         Continue C.R. after POST:  [Off]
 +
<br>
 
Boot
 
Boot
 
   Boot priority order:
 
   Boot priority order:

Revision as of 11:42, 27 February 2013

Overview

A dedicated Server hardware is required to host the HiPath Cordless IP Server appliance software in order to deploy a larger HiPath Cordless IP system (with an increased number of installed DECT IP Base Stations and/or an increased number of registered Gigaset/OpenStage S/SL Professional DECT phones).

The features and requirements of HiPath Cordless IP (e.g. network requirements) are not changed even if the HiPath Cordless IP Server runs on a dedicated Server hardware.

The Server's Operating System used with HiPath Cordless IP is based on a Linux distribution for embedded device: OpenWrt.

The Operating System forms part of the Software delivery CD-ROM (the HiPath Cordless IP Server): The Operating System came preconfigured for the usage with the below mentioned Fujitsu PRIMERGY hardware Server (e.g. all the required driver are already compiled into the Operation System).

Main advantage with this approach is the quick and easy installation process of the entire HiPath Cordless IP Server software once the specified hardware Server is used.

Fujitsu PRIMERGY RX/TX Server supported

Fujitsu PRIMERGY RX100 S7 (released since February 2013)

Order Number of this Server at Fujitsu is CUZ:1385V203-SEN08

If you change the Motherboard of this Fujitsu Server please consider to apply the BIOS configuration reported below:

Advanced

 > SATA Configuration
    SATA Mode Selection:	[AHCI]
    Aggressive LPM Support	[Enabled]


Server Mgmt

 > Console Redirection
    Com Port Address:          	[Serial 1]
    Baud Rate:                 	[115.2K]
    Console Type:              	[VT100]
    Flow Control:              	[None]


Boot

  Boot priority order:
    Boot Option #1: [P0: ST500NM0011]
    Boot Option #2: [P4: TSSTcorp CDDVDW SN-208AB]
    Boot Option #3: [Disabled]

Fujitsu PRIMERGY TX150 S7 (declared Phase Out by Fujitsu, superseded by TX150 S8)

Order Number of this Server at Fujitsu was CUZ:1265V101-SEN04

If you change the Motherboard of this Fujitsu Server please consider to apply the BIOS configuration reported below:

Advanced

  > Advanced System Configuration
     SATA Mode Selection:         [AHCI]


Server

   > Console Redirection
       Com Port Address:          [On-board COM A]
       Baud Rate:                 [115.2K]
       Console Type:              [VT100]
       Flow Control:              [None]
       Continue C.R. after POST:  [Off]


Boot

  Boot priority order:
      1:  SATA 1: WDC WD2502ABYS-50B7A0-(S1)
      2:  SATA CD: HL-DT-ST DVDRAM GH40N-(S5)


This configuration is valid for BIOS version equal to 1.16.