Views

Difference between revisions of "HiPath Cordless IP - Server HW"

The Wiki of Unify contains information on clients and devices, communications systems and unified communications. - Unify GmbH & Co. KG is a Trademark Licensee of Siemens AG.

Jump to: navigation, search
 
(One intermediate revision by one other user not shown)
Line 15: Line 15:
 
Main advantage with this approach is the quick and easy installation process of the entire HiPath Cordless IP Server software once the specified hardware Server is used.  
 
Main advantage with this approach is the quick and easy installation process of the entire HiPath Cordless IP Server software once the specified hardware Server is used.  
  
== Fujitsu PRIMERGY RX/TX Server supported ==
+
Currently a Fujitsu RX100S8 server with special BIOS settings is required as the server for the HiPath Cordless IP Server SW. The Fujitsu server can be ordered in the same way as all other HiPath Cordless IP components.
  
=== Fujitsu PRIMERGY RX100 S7 (released since February 2013) ===
+
If you change the Motherboard of the Fujitsu Server please consider to apply the correct BIOS configuration. In that case contact 
 
+
[mailto:ulrich.mitreuter@unify.com product management]
Order Number of this Server at Fujitsu is CUZ:1385V203-SEN08<br>
 
 
 
If you change the Motherboard of this Fujitsu Server please consider to apply the BIOS configuration reported below:
 
 
 
Advanced
 
  > SATA Configuration
 
    SATA Mode Selection: [AHCI]
 
    Aggressive LPM Support [Enabled]
 
<br>
 
Server Mgmt
 
  > Console Redirection
 
    Com Port Address:          [Serial 1]
 
    Baud Rate:                [115.2K]
 
    Console Type:              [VT100]
 
    Flow Control:              [None]
 
<br>
 
Boot
 
  Boot priority order:
 
    Boot Option #1: [P0: ST500NM0011]
 
    Boot Option #2: [P4: TSSTcorp CDDVDW SN-208AB]
 
    Boot Option #3: [Disabled]
 
 
 
=== Fujitsu PRIMERGY TX150 S7 (declared Phase Out by Fujitsu, superseded by TX150 S8) ===
 
 
 
Order Number of this Server at Fujitsu was CUZ:1265V101-SEN04<br>
 
 
 
If you change the Motherboard of this Fujitsu Server please consider to apply the BIOS configuration reported below:
 
 
 
Advanced
 
  > Advanced System Configuration
 
      SATA Mode Selection:        [AHCI]
 
<br>
 
Server
 
    > Console Redirection
 
        Com Port Address:          [On-board COM A]
 
        Baud Rate:                [115.2K]
 
        Console Type:              [VT100]
 
        Flow Control:             [None]
 
        Continue C.R. after POST:  [Off]
 
<br>
 
Boot
 
  Boot priority order:
 
      1:  SATA 1: WDC WD2502ABYS-50B7A0-(S1)
 
      2:  SATA CD: HL-DT-ST DVDRAM GH40N-(S5)
 
<br>
 
This configuration is valid for BIOS version equal to 1.16.
 

Latest revision as of 11:46, 24 July 2014

Overview

A dedicated Server hardware is required to host the HiPath Cordless IP Server appliance software in order to deploy a larger HiPath Cordless IP system (with an increased number of installed DECT IP Base Stations and/or an increased number of registered Gigaset/OpenStage S/SL Professional DECT phones).

The features and requirements of HiPath Cordless IP (e.g. network requirements) are not changed even if the HiPath Cordless IP Server runs on a dedicated Server hardware.

The Server's Operating System used with HiPath Cordless IP is based on a Linux distribution for embedded device: OpenWrt.

The Operating System forms part of the Software delivery CD-ROM (the HiPath Cordless IP Server): The Operating System came preconfigured for the usage with the below mentioned Fujitsu PRIMERGY hardware Server (e.g. all the required driver are already compiled into the Operation System).

Main advantage with this approach is the quick and easy installation process of the entire HiPath Cordless IP Server software once the specified hardware Server is used.

Currently a Fujitsu RX100S8 server with special BIOS settings is required as the server for the HiPath Cordless IP Server SW. The Fujitsu server can be ordered in the same way as all other HiPath Cordless IP components.

If you change the Motherboard of the Fujitsu Server please consider to apply the correct BIOS configuration. In that case contact product management