Views

Asterisk Feature Busy Lamp Field (BLF)

The Wiki of Unify contains information on clients and devices, communications systems and unified communications. - Unify GmbH & Co. KG is a Trademark Licensee of Siemens AG.

Revision as of 08:32, 9 February 2009 by Horemu (talk | contribs)
Jump to: navigation, search

The busy lamp feature allows users to monitor the dialog state of another phone/user extension. This is indicated by the LEDs in an FPK. This feature is called "Busy Lamp Field" in the Asterisk community. Sometime the term 'Direct Station Selection' is used for the same functionality.

The feature is available for OpenStage 40/60/80.

The feature description uses always the same example background with fixed names, numbers and IP addresses. The example configuration can be found in Asterisk Feature Example Configuration.

For Users

The basic Busy Lamp field feature allows the user to monitor the dialog state of another phone/user extension. The dialog state is shown by a distinct LED behavior:

  • LED off -> Watched extension is idle
  • LED blinking -> Watched extension is ringing
  • LED on -> Watched extension is busy/connected

In the basic configuration pressing the FPK will call the monitored persion in any call state.

Example:

There are four users: Leo, Alice, Joe and Bob. Leo is watching the extensions of Alice, Bob and Joe. Each of the extensions are configured on an specific FPK. The example shows the three different extension status. Joe is talking to annother persion, Alice gets a call, her phone is ringing and Bob is in idle like Leo is. The following picture shows this example:


Extension status on FPK: Joe is in busy, Alice is in ringing and Bob is in idle state


Leo can see at any time the status of the other people by watching the LEDs on the FPK.

Using FPK

The OpenStage phone supports the BLF functionality in two differen FPK functions types.

The BLF-Type can be used in scenarious, where team members want to pick up the call for each other team members.

The Server Feature-Type can be used in receiptions for example, where the receptionist wants to see the call status of all employees, but never wants to pick up the call for someone.

The OpenStage FPK is able to perform different actions depending on the satus of the FPK.

BLF-Type:


LED Status Action by Key Press
off Wachted Party is called
blinking Incoming call for watched persion is picked up
on Nothing


Server Feature-Type:


LED Status Action by Key Press
off Wachted Party is called
blinking Wachted Party is called
on Wachted Party is called


For Administrators

Using FPK "BLF"

The FPK are administrated as BLF. This is one option of the FPK programming options. The configuration can be found in

Administrator Pages -> System -> Features -> Program Keys:

The FPK function is ‘BLF’. Select this option and press ‘Edit

Basic BLF Configuration with BLF Key

Within the server feature four options are given:

Basic BLF Configuration Parameters

Key label - This is the label of the selected FPK
Monitored Phone - This is the SIP URI/phone number of the monitored phone
Audible Alert - These checkbox activates a short beep/ringing alert, if LED status changes to blinking
Popup on alert - These checkbox activates a popup message, if LED status changes to blinking

Example:

If Bob has the extension numer 222, the parameters will be:

Key label - Bob
Monitored Phone - 222
Audible Alert - yes, a short beep or ringing tone is done, if Bob gets a call.
Popup on alert - yes, a popup is shown, if Bob gets a call.

Remark:

It migth be neccessry to configure an BLF Pickup Group Feature Key to enable the function. This can be done at

Administrator Pages -> System -> Features -> Services:

BLF Pickup Code Configuration

Using FPK "Server Feature"

The FPK are administrated as Server Key. This is one option of the FPK programming options. The configuration can be found in

Administrator Pages -> System -> Features -> Program Keys:

The FPK function is ‘Server Feature’. Select this option and press ‘Edit

Basic BLF Configuration with Server Key

Within the server feature four options are given:

Basic BLF Configuration Parameters

Key label - This is the label of the selected FPK
Feature Code - This code is sent within an INVITE message, if the key is pressed in idle status
DTMF Digits - These Digits are sent as DTMF signals, if the key is pressed during a call
LED control - A Subscribtion is sent to the given URL

Example:

If Bob has the extension numer 222, the parameters will be:

Key label - Bob
Feature Code - 222, pressing the FPK will always call Bob independant of his line status..
DTMF Digits - n.a.., not neccessary in this feature
LED control - 222@192.168.6.10, a subscription for the LED will be sent to the server at the IP address 192.168.6.10. If no IP address is given, the request will be automatically sent to the configured SIP proxy server.

Technical Background

The BLF feature gives the user the possiblity to watch one other users dialog state. To support the feature RFC 4235 is used.

This document defines a dialog event package for the SIP Events architecture, along with a data format used in notifications for this package. The dialog package allows users to subscribe to another user and to receive notification of the changes in state of INVITE -initiated dialog usages in which the subscribed- to user is involved.

The framework is startet with an initial subscription from the watching phone. The following table shows the subscription from Leo for Joe's extension:


192.168.0.247 192.168.0.10 SIP Message
Request: SUBSCRIBE SIP: Request: SUBSCRIBE sip:333@192.168.0.10:5060
Joe's phone ------------------> Asterisk
Status: 401 Unauthorized SIP: Status: 401 Unauthorized
Joe's phone <------------------ Asterisk
Request: SUBSCRIBE SIP: Request: SUBSCRIBE sip:333@192.168.0.10:5060
Joe's phone ------------------> Asterisk
Status: 200 OK SIP: Status: 200 OK
Joe's phone ------------------> Asterisk


After that the Asterisk PBK sends Notification to Leo's phone to tell the status of Joe's line. The table below shows an example Notification:


192.168.0.247 192.168.0.10 SIP Message
Request: NOTIFY SIP: Request: NOTIFY sip:444@192.168.0.247:5060
Joe's phone <------------------ Asterisk
Status: 200 OK SIP: Status: 200 OK
Joe's phone ------------------> Asterisk


Within the Notify the line status is delivered in the XML body. The OpenStage phone support three line status

Idle (LED off)

The idle state is notified within the dialog event subscription. The dialog state in the message body is terminated or left empty.

Here is an example for Joes idle state sent to Leo.


Message:
NOTIFY sip:444@192.168.0.247:5060;transport=udp SIP/2.0
v: SIP/2.0/UDP 192.168.0.10:5060;branch=z9hG4bK38e76e71;rport
f: <sip:333@192.168.0.10:5060;transport=udp>;tag=as4aa60d2a
t: Leo Demo 444 <sip:444@192.168.0.10>;tag=cc29a24a90;epid=SCBCC441
m: <sip:333@192.168.0.10>
i: 46c0a8f00bff87e0
CSeq: 102 NOTIFY
User-Agent: Asterisk Gemeinschaft
Max-Forwards: 70
o: dialog
c: application/dialog-info+xml
Subscription-State: active
l: 208
Body:
<?xml version="1.0"?>
<dialog-info xmlns="urn:ietf:params:xml:ns:dialog-info" version="0" state="full" entity="sip:333@192.168.0.10:5060">
<dialog id="333">
<state>terminated</state>
</dialog>
</dialog-info>

Ringing (LED blinking)

The ringing state is notified within the dialog event subscription. The dialog state in the message body is early.

Here is an example for Joes ringing state sent to Leo.


Message:
NOTIFY sip:444@192.168.0.247:5060;transport=udp SIP/2.0
v: SIP/2.0/UDP 192.168.0.10:5060;branch=z9hG4bK66a6adf2;rport
f: <sip:333@192.168.0.10:5060;transport=udp>;tag=as6576596c
t: Leo Demo 444 <sip:444@192.168.0.10>;tag=9304448a7d;epid=SCBCC441
m: <sip:333@192.168.0.10>
i: 7a5553c742843273
CSeq: 103 NOTIFY
User-Agent: Asterisk Gemeinschaft
Max-Forwards: 70
o: dialog
c: application/dialog-info+xml
Subscription-State: active
l: 225
Body:
<?xml version="1.0"?>
<dialog-info xmlns="urn:ietf:params:xml:ns:dialog-info" version="1" state="full" entity="sip:333@192.168.0.10:5060">
<dialog id="333" direction="recipient">
<state>early</state>
</dialog>
</dialog-info>

Connected/Busy (LED on)

The connected/busy state is notified within the dialog event subscription. The dialog state in the message body is confirmed.

Here is an example for Joes connected/busy state sent to Leo.


Message:
NOTIFY sip:444@192.168.0.247:5060;transport=udp SIP/2.0
v: SIP/2.0/UDP 192.168.0.10:5060;branch=z9hG4bK3685f474;rport
f: <sip:333@192.168.0.10:5060;transport=udp>;tag=as05967368
t: Leo Demo 444 <sip:444@192.168.0.10>;tag=2ad7b4ac94;epid=SCBCC441
m: <sip:333@192.168.0.10>
i: 4a6a3f0f21b83343
CSeq: 103 NOTIFY
User-Agent: Asterisk Gemeinschaft
Max-Forwards: 70
o: dialog
c: application/dialog-info+xml
Subscription-State: active
l: 207
Body:
<?xml version="1.0"?>
<dialog-info xmlns="urn:ietf:params:xml:ns:dialog-info" version="1" state="full" entity="sip:333@192.168.0.10:5060">
<dialog id="333">
<state>confirmed</state>
</dialog>
</dialog-info>

Complete Example Call Flow

A example call flow has been recorded. At the end of this call flow Joe is in busy (LED on), Alice is in ringing (LED blinking) and Bob is in idle state (LED off).


zip.png  BLFBasicCallFlow the complete example call flow

See also